Open safety recalls, the components owners report failing most often, crash-test results and running costs for the 2009 Mazda MAZDA6, assembled from NHTSA and EPA records.
Everything on this page applies to the model as a whole. Run its VIN to decode that exact car, its engine, trim, assembly plant and factory equipment, alongside these records.
Open a VIN recordRecalls and complaints are filed against a specific model year, so figures differ from one year to the next even within a single generation. See every Mazda MAZDA6 year.
No EPA fuel-economy match for this model. Naming may differ, or it predates EPA records.
The parts named most often across 386 owner complaints filed with NHTSA for this make, model and year.
4 crashes · 5 injured
1 crash
1 crash
1 fire
Complaints are self-reported and skew toward problems people find alarming, so read this as where to look rather than as a defect rate.
Rear cross member broke due to corrosion breaking off lateral arm from driver side of cross member, I may add the front crossmember was repaired due to recall for extreme corrosion not too long ago, as I research this problem I uncover many owners of this vehicle having the same issue in the northeast,even with much lower mileage.mazda should be held accountable.$3,926.62 for part alone on Mazda parts.com
The rear subframe rusted out and my control arm broke off! This is extremely serious and because there is no recall I’m going to have to buy an another vehicle. Please issue a recall. I’ve read forms about this and many others have had the same issue with the rear subframe corroding and rotting out.
My rear subframe rusted thru and has holes in it. It is too dangerous to drive and mazda won't recall the rear like the front subframe knowing that a lot of people are suffering from the same issue. A subframe should last a long time. My mechanic inspected the car and feels like it's not safe to drive.
This car was purchased in 2017 and maintenanced regularly. We recently took it to have the oil changed and to check out a noise that was coming from the passenger side. We were told that the subframe was rusted so badly it was too dangerous to drive and would cost $7k to repair. That caught us by surprise and we ended up having to buy a car by the next day. We traded the car in… However, I started doing some research and noted that this is very common and there was a recall between 2010 and 2014. I’m pretty upset that we lost this car without having any recall notification after the purchase. Could this have been taken care of instead of having to get a new car?
Component or System that Failed: The front subframe on my 2009 Mazda 6i Touring is completely rusted through. There are holes in the frame and large flakes of rusted metal breaking off. The car is available for inspection if needed. Safety Risk: This is a serious safety concern because if the subframe fails, I could lose steering or suspension control while driving. That would put me and other drivers at immediate risk of an accident. Reproduction / Confirmation: An independent mechanic confirmed the problem and told me the car is unsafe to drive in its current condition. Inspection: The vehicle had the original Mazda subframe corrosion recall performed years ago, but now the same exact problem has come back. The car has not yet been re-inspected by Mazda, but the severity of the rust is obvious. Warning Lamps / Symptoms: There were no warning lights or messages before this happened. The issue was only noticed when the rust and holes became visible on the underside of the car during a recent inspection.
Hello, My name is [XXX] . I took our Mazda 6 in for wheel balance and alignment and was informed of very serious rust issues in the rear suspension. I was pretty shocked at what they showed me. I worked at Raben Tire for 10 years and I've never seen anything like this. I have two retired mechanic friends look at it, and they (along with the mechanic from firestone) said they cannot even fathom how this level of rust is possible (80+% of the miles on this vehicle are highway). One of my retired mechanic friends started looking into it and said he'd noticed the 09 Mazda recalls for suspension rust. We all thought that made sense given how immensely abnormal this rusting is. The recall list sent to me says "front" suspension. I'm not sure why the front is listed and not the rear, but this, to all of us, is very clearly faulty (the rusting is INCREDIBLY abnormal) and we believe should be considered as part of the suspension rust recall (there are no rusting issues anywhere else). Ive provided pictures. This is incredibly unsafe. The rear suspension could collapse at any moment while driving and cause casualties. Thank you for your time, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The front and rear crossmembers have significant rust. The front has holes and chunks of metal missing due to rust corrosion. The rear has flaking and is deeply pockmarked with rust. These are structural components. Failure can lead to a crash.
The passenger crash pad has deteriorated and become sticky and cracked. This may affect deployment of airbag and perhaps allow outside environmental elements to affect the airbag. The takata fiasco being an example of environmental factors affecting airbag safety.
The rear Suspension Frame has failed due to corrosion. The right rear tire has worn severely from the premature failure of that part on the right side. I feel it was a defect in Engineering by Mazda. My email: [XXX] Mobile: [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The rear frame has failed due to corrosion on the right side. The rear passenger tire is canted in on the topside worn severely worn. This was noted when I drove home from my job. This is a critical part of the vehicle and should've never failed. I'm hopeful to hear from the NHTSB for a repair to be done properly by Mazda;
Rear suspension cross-member corroded to the point that a minor pothole separated the right lower control arm mounting point from the cross-member, rendering the car undrivable. The rest of the car is fairly rust-free.
Rear subframe corrosion
Showing 12 of 386 complaints.
NHTSA has issued a do-not-drive warning covering 4 recalls on this make, model and year. Repairs are free at any franchised dealer.
Recalls are issued per model. Confirm whether this specific car has already been repaired using its VIN, free, at any franchised dealer or on nhtsa.gov/recalls.
NHTSA lists 10 recalls for this make, model and year. Recalls apply to the model, so some may already be fixed on this specific car. A dealer can confirm from the VIN.
Issue: Mazda North American Operations (Mazda) is recalling certain 2007-2012 CX-7, CX-9, and 2009-2012 Maza6 vehicles. These vehicles had their passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. The recall began December 3, 2019. Owners may contact Mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 1317F. Note: This recall supersedes recalls 16V356 and 17V012.
Campaign 19V782000
Issue: Mazda North America Operations (Mazda) is recalling certain 2009-2011 Mazda6, and 2007-2011 CX-7 and CX-9 vehicles. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Risk: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the passenger frontal air bag inflator with an alternate inflator, free of charge. The recall began on August 30, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F. Note: This recall supersedes recall 16V356 and all vehicles that were not remedied under that campaign are now covered by this one.
Campaign 17V429000
Issue: Mazda North American Operations (Mazda) is recalling certain 2013 Mazda6 and CX-9 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, unless covered in "Zone A," Mazda is recalling certain 2010 Mazda6, CX-7 and CX-9 vehicles sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, unless covered in Zone A or Zone B, Mazda is recalling certain 2009 Mazda6, CX-7, and CX-9 vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate inflator, free of charge. The recall began March 2, 2018. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F.
Campaign 18V018000
Issue: Mazda North America Operations (Mazda) is recalling certain 2012 CX-7, CX-9 and Mazda6 vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Mazda is recalling certain 2009 CX-7, CX-9 and Mazda6 vehicles sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above, Mazda is recalling certain 2007-2008 CX-7 and CX-9 sold, or ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Risk: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the front passenger side air bag inflator with an alternate inflator, free of charge. The recall began October 4, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F. Note: This recall supersedes recall 17V-012.
Issue: Mazda North American Operations (Mazda) is recalling certain 2009-2010 Mazda Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Wisconsin and the District of Columbia. The front cross member may corrode after exposure to road salt.
Risk: Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.
Remedy: Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began March 18, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I.
Campaign 18V631000
Issue: Mazda North American Operations (Mazda) is recalling certain model year 2009-2010 Mazda6 vehicles manufactured February 4, 2008, to December 3, 2009. The protective coating may not have been properly applied to the air bag control unit (ACU) and, as a result, moisture may damage the unit causing it to malfunction.
Risk: Failure of the ACU would illuminate the air bag warning light and prevent the air bags from deploying in the event of a crash, increasing the risk of injury.
Remedy: Mazda dealers will replace the ACU, free of charge, however parts are not currently available. The recall began June 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9816H.
Campaign 16V594000
Issue: Mazda is recalling certain model year 2009-2013 Mazda6 vehicles manufactured February 4, 2008, through August 24, 2012. The door latch mounting screws may become loose.
Risk: If all three door latch mounting screws become excessively loose the door latch mechanism would not engage and the door might open while the vehicle is in motion increasing the risk of accident or injury.
Remedy: Mazda will notify owners, and dealers will apply a thread locking adhesive to the door screws and retorque them, free of charge. The recall began on October 29, 2013. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number is 7013I.
Campaign 13V425000
Issue: MAZDA IS RECALLING CERTAIN MODEL YEAR 2009-2010 MAZDA6 VEHICLES MANUFACTURED FROM APRIL 8, 2008, THROUGH FEBRUARY 8, 2010. A CERTAIN TYPE OF SPIDER MAY WEAVE A WEB IN THE EVAPORATIVE CANISTER VENT LINE AND THIS MAY CAUSE A RESTRICTION IN THE LINE. IF THIS OCCURS, THE FUEL TANK PRESSURE MAY BECOME EXCESSIVELY NEGATIVE WHEN THE EMISSION CONTROL SYSTEM WORKS TO PURGE THE VAPORS FROM THE CANISTER.
Risk: AS THE CANISTER IS PURGED REPEATEDLY DURING NORMAL OPERATION, THE STRESS ON THE FUEL TANK MAY EVENTUALLY RESULT IN A CRACK, POTENTIALLY LEADING TO FUEL LEAKAGE AD AN INCREASED RISK OF FIRE.
Remedy: DEALERS WILL INSPECT AND CLEAN UP THE CANISTER VENT LINE, AND INSTALL A SPRING TO PREVENT THIS TYPE OF SPIDER FROM ENTERING THE VENT LINE. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE MARCH 25, 2011. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Campaign 11V134000
Issue: MAZDA IS RECALLING 29,000 MY 2009 MAZDA6. THE OUTER DOOR HANDLES MAY STICK WHICH MAY PREVENT THE DOOR FROM LATCHING. THIS SITUATION MAY ALLOW THE DOOR TO OPEN WHILE THE VEHICLE IS IN MOTION.
Risk: DRIVING THE VEHICLE WITH THE DOOR UNLATCHED COULD LEAD TO AN UNBELTED OCCUPANT BEING EJECTED AND COULD RESULT IN DEATH OR INJURY.
Remedy: DEALERS WILL INSPECT THE DOOR HANDLES AND IF NECESSARY REPAIR OR REPLACE THE HANDLES FREE OF CHARGE. THE RECALL BEGAN ON FEBRUARY 13, 2009. OWNERS MAY CONTACT MAZDA AT 1-800-222-5500.
Campaign 09V043000
Issue: THULE, INC. IS RECALLING 2,323 OWNER-INSTALLED ROOF-MOUNTED FIT KITS, MODELS 3068 AND 3069, MANUFACTURED BETWEEN JANUARY 1, 2008 AND FEBRUARY 28, 2009 THAT ARE USED WITH THULE PODIUM FOOT PACKS, MODELS 460 AND 460R. THESE FIT KITS WERE SOLD AS AFTERMARKET EQUIPMENT FOR USE ON THE VEHICLES LISTED ABOVE. THE BOLT(S) USED TO SECURE THE FOOT TO THE VEHICLE WAS MANUFACTURED TO A HARDNESS THAT MAY CAUSE THE BOLT(S) TO BE BRITTLE AND POTENTIALLY BREAK UNDER STRESS.
Risk: THIS MAY RESULT IN THE BOLT(S) SNAPPING OFF DURING USE OR WITHOUT A LOAD. THE UNSECURED RACK AND LOAD CAN THEN COME LOOSE WHILE DRIVING CREATING A POTENTIAL ROAD HAZARD, POSSIBLY RESULTING IN A VEHICLE CRASH.
Remedy: THULE WILL MAIL A RETRO FIT KIT ALONG WITH REPAIR INSTRUCTIONS TO OWNERS FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE APRIL 13, 2009. OWNERS MAY CONTACT THULE TOLL-FREE AT 1-800-238-2388.
Campaign 09E011000
Campaign 17V457000
NHTSA frontal crash test
2 open NHTSA investigations into this model. Investigations come before recalls, so these are potential defects not yet covered by one.
Rated configuration: 2009 Mazda6 4-DR. w/SAB