Open safety recalls, the components owners report failing most often, crash-test results and running costs for the 2008 Toyota Sequoia, assembled from NHTSA and EPA records.
Everything on this page applies to the model as a whole. Run its VIN to decode that exact car, its engine, trim, assembly plant and factory equipment, alongside these records.
Open a VIN recordRecalls and complaints are filed against a specific model year, so figures differ from one year to the next even within a single generation. See every Toyota Sequoia year.
No EPA fuel-economy match for this model. Naming may differ, or it predates EPA records.
NHTSA lists 9 recalls for this make, model and year. Recalls apply to the model, so some may already be fixed on this specific car. A dealer can confirm from the VIN.
Issue: Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2008-2022 Sequoia and 2007-2021 Tundra vehicles. The power steering gear assembly may have been manufactured incorrectly, which can result in an oil leak.
Risk: An oil leak may cause a sudden loss of power steering assist, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the power steering gear assembly as necessary, free of charge. Owner notification letters were mailed on January 21, 2022. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are 21TB10 and 21TA10.
Campaign 21V920000
Issue: Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain JTEKT power steering gear assembly service parts for 2007-2021 Tundra and 2008-2022 Sequoia, part numbers 44250-0C160, 44250-0C131, 44250-0C170, and 11250-0C121. The power steering gear assembly may have been manufactured incorrectly, which can result in an oil leak.
Risk: An oil leak may cause a sudden loss of power steering assist, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the power steering gear assembly, free of charge. Owner notification letters were mailed on February 17, 2022. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is 21TH01.
Campaign 21E103000
Issue: Southeast Toyota Distributors, LLC (SET) is recalling certain 2005-2011 4Runner, Highlander, Sequoia, and Sienna, 2005-2010 Avalon and Tundra, 2006-2008 Camry Solara, 2006-2010 Highlander hybrid, 2006-2011 Rav4 and Tacoma, 2007-2010 FJ Cruiser, 2007-2011 Camry hybrid, 2009-2010 Venza, 2010-2012 Prius, 1988-1990 and 2005-2010 Camry, and 1989 and 2009-2010 Corolla vehicles equipped with aftermarket accessory seat heaters with a copper strand heating element. The electrical wiring in the seat heaters may be damaged when the seat cushion is compressed.
Risk: If damaged, the copper strand heating element may short circuit, increasing the risk of a fire.
Remedy: SET will notify owners, and dealers will disconnect the seat heaters, free of charge, and refund the purchase price of the seat heater accessory. The recall began on July 14, 2016. Owners may contact SET customer service at 1-866-405-4226. SET number for this recall is SET16B.
Campaign 16V396000
Issue: Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2010-2011 Prius and Corolla, 2009-2011 Venza, 2006-2010 Avalon, 2007-2010 FJ Cruiser, 2005-2011 Sienna and Sequoia, 2006-2011 Tacoma 4x2 and 4x4, Camry, Highlander, Tundra 4x2 and 4x4, and 2007-2011 Rav4 and 4Runner. The affected vehicles may experience compression of the seat cushion which may damage the seat heater wiring.
Risk: Damage to the seat heater wiring could cause the wires to short, increasing the risk of the seat burning and causing personal injury to the occupant.
Remedy: SET will notify owners, and dealers will disconnect the heaters with copper strand heating elements and refund the purchase price of the seat heater accessory, free of charge. The recall is expected to began in January 2015. Owners may contact SET customer service at 1-866-405-4226.
Campaign 14V743000
Issue: TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 THROUGH 2011 FJ CRUISER, LAND CRUISER, TACOMA, SEQUOIA AND TUNDRA VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 138, "TIRE PRESSURE MONITORING SYSTEM (TPMS)." WHEN FACTORY-INSTALLED WHEELS AND TIRES WERE REPLACED WITH TOYOTA AUTHORIZED ACCESSORY WHEELS AND LT TIRES PRIOR TO FIRST SALE, THE TIRE PRESSURE MONITORING SYSTEMS WERE NOT RE-CALIBRATED CORRECTLY AND THEREFORE DO NOT START ILLUMINATING THE LOW TIRE PRESSURE WARNING TELLTALE AT THE REQUIRED MINIMUM ACTIVATION PRESSURE.
Risk: FAILURE TO WARN OF TIRE DEFLATIONS IS A NON-COMPLIANCE WITH FMVSS 138 AND COULD LEAD TO TIRE FAILURE INCREASING THE RISK OF A CRASH.
Remedy: FOR THE LAND CRUISER, SEQUOIA, TACOMA AND TUNDRA VEHICLES, THE DEALER WILL RE-CALIBRATE THE TIRE PRESSURE MONITORING SYSTEM ON AFFECTED VEHICLES AND INSTALL AN UPDATED TIRE AND LOADING INFORMATION LABEL AT NO CHARGE. FOR THE FJ CRUISER VEHICLES, THE TPMS CANNOT BE RESET SO THE ELECTRONIC CONTROL UNIT (ECU) FOR THE TPMS WILL BE REPLACED. TOYOTA IS CURRENTLY DEVELOPING THE REMEDY ECU. IF AN OWNER IS NOT CERTAIN WHETHER HIS OR HER VEHICLE IS EQUIPPED WITH THESE ACCESSORIES, PLEASE CONTACT ANY TOYOTA DEALER FOR AN INSPECTION AT NO CHARGE. THE SAFETY RECALL BEGAN ON MARCH 31, 2011. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Campaign 11V148000
Issue: Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the switch assemblies. Irregularities in this lubrication process may cause the power window master switch assemblies to malfunction and overheat.
Risk: If the switch overheats, it may melt, possibly resulting in a fire.
Remedy: Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1-800-762-2737.
Campaign 12V491000
Issue: SOUTHEAST TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2011 PASSENGER VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.
Risk: A DRIVER MAY OVERLOAD A VEHICLE WHICH MAY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT SOUTHEAST TOYOTA AT 1-800-301-6859.
Campaign 10V036000
Issue: GULF STATES TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2010 VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD BETWEEN SEPTEMBER 1, 2005 AND JUNE 2, 2008 WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.
Risk: THIS DOES NOT MEET THE STANDARD REQUIREMENTS.
Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. DEALERS WILL ALSO CORRECT THE OWNER'S MANUAL. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT GULF STATES TOYOTA AT 713-580-3300.
Campaign 10V035000
Issue: TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2010 AVALON, MODEL YEAR 2007-2010 CAMRY, MODEL YEAR 2009-2010 COROLLA, COROLLA MATRIX, RAV4, MODEL YEAR 2010 HIGHLANDER, MODEL YEAR 2008-2010 SEQUOIA, AND MODEL YEAR 2007-2010 TUNDRA VEHICLES. DUE TO THE MANNER IN WHICH THE FRICTION LEVER INTERACTS WITH THE SLIDING SURFACE OF THE ACCELERATOR PEDAL INSIDE THE PEDAL SENSOR ASSEMBLY, THE SLIDING SURFACE OF THE LEVER MAY BECOME SMOOTH DURING VEHICLE OPERATION. IN THIS CONDITION, IF CONDENSATION OCCURS ON THE SURFACE, AS MAY OCCUR FROM HEATER OPERATION (WITHOUT A/C) WHEN THE PEDAL ASSEMBLY IS COLD, THE FRICTION WHEN THE ACCELERATOR PEDAL IS OPERATED MAY INCREASE, WHICH MAY RESULT IN THE ACCELERATOR PEDAL BECOMING HARDER TO DEPRESS, SLOWER TO RETURN, OR, IN THE WORST CASE, MECHANICALLY STUCK IN A PARTIALLY DEPRESSED POSITION.
Risk: THE ACCELERATOR PEDAL MAY BECOME HARD TO DEPRESS, SLOW TO RETURN TO IDLE, OR, IN THE WORST CASE, MECHANICALLY STUCK IN A PARTIALLY DEPRESSED POSITION, INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL INSTALL A REINFORCEMENT BAR IN THE ACCELERATOR PEDAL WHICH WILL ALLOW THE PEDAL TO OPERATE SMOOTHLY. GM WILL NOTIFY OWNERS FOR THE PONTIAC VIBE PLEASE SEE 10V-018. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON FEBRUARY 5, 2010 AND WILL BE COMPLETED ON MARCH 15, 2010. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Campaign 10V017000
The parts named most often across 66 owner complaints filed with NHTSA for this make, model and year.
2 crashes · 2 injured
Complaints are self-reported and skew toward problems people find alarming, so read this as where to look rather than as a defect rate.
While accelerating to pass a vehicle that was signaling and operating well below the speed limit, my vehicle experienced sudden and continued unintended acceleration. I was able to bring the vehicle to a stop while fighting against the engine within an intersection but the engine continued building revs, bouncing off the limiter while my foot was entirely removed from the accelerator pedal and fully applied to the brake. During this time I had moved the gear selector to neutral, only furthering the engine's revs, and attempted to place the vehicle into park without success, before having to reach beneath my dashboard, foot still on the brake, to pull the accelerator pedal up. I verified both visually and by feel that the pedal was stuck in it's position entirely on it's own, there was no outside object or floormat inhibiting it's ability to return.
Odometer Fraud. The contact purchased a 2008 Toyota Sequoia. The contact discovered a mileage discrepancy after the purchase. The vehicle was a dealer sale. At the time of purchase, the vehicle mileage was 143,000. It was later discovered, when the contact received the Title, the mileage was 248,000.
The drivers seat belt sometime does not retract. One of the seat belts in the middle row retracts slowly or sometimes does not retract. Another seatbelt is very tough to pull out to buckle. I just purchased this vehicle so I’m not sure how long the seatbelts have been an issue.
My wife pulled out of a parking lot and there was a loud noise and the vehicle began to shudder violently. Approximate speed was 10 mikes an hour and she was able to stop. The drivers side rear suspension airbag had broken through the lower control arm, and was under the rear driver side tire. It appears some frame members are cracked as well. Had this happened at highway speeds, it may have resulted in a catastrophic accident. Writer contacted Toyota, as I do not recall being notified of their ZH9 frame replacement program that resulted from a class action settlement, and the rear of the frame is horribly rusted. Vehicle probably would have qualified at that time to be fixed, but am now out of the window. Manufacturers should be made to notify via certified mail, so they know their customers received notifications like this.
The contact owns a 2008 Toyota Sequoia. The contact stated that while the vehicle was at the independent mechanic for an oil change, the mechanic informed her husband that the chassis was severely rusted. The dealer and other unknown dealers were notified of the failure and informed the contact that they could not repair the vehicle under Toyota Campaign Number: ZH7 because the campaign had expired. The manufacturer was notified of the failure and confirmed the assessment from the dealers. The vehicle was not repaired. The failure mileage was approximately 30,000. The VIN was unavailable.
The contact owns a 2008 Toyota Sequoia. The contact stated that while the vehicle was in for routine service, the independent mechanic discovered that the rear subframe was severely damaged due to rust and corrosion. The contact was advised that holes were present in the subframe, and the vehicle was unsafe to drive. The vehicle was not repaired. The local dealer and manufacturer were notified of the failure and informed that the vehicle was no longer qualified under the Extended Warranty Coverage for the failure. The failure mileage was 168,000. The VIN was not available.
A valve spring in the engine failed causing one cylinder to fail as well. The failure fortunately happened at low speed and the engine didn't seize. This a known problem with Toyota V8s of this model year and was the reason for a recall of Lexus vehicles with the same engine. Had this happened at highway speed, the engine, we were told, could have experienced a total failure causing the engine to seize likely leading to a serious accident. The car is available for inspection at the moment, but this failure requires a total engine rebuild or an engine replacement which are both very costly and we may have to purchase a new car. The car has not been inspected by Toyota, police, insurance or anyone other than a car service center. There were no warning lights, messages or any symptoms prior to the failure. It was sudden with no warning at all. The car has been very well maintained over the years with regular maintenance done on a consistent schedule.
Activation of VSC off and slip indicator flashing.
The contact owns a 2008 Toyota Sequoia. The contact stated that while the vehicle was at the dealer for an unknown repair, the dealer informed the contact that the sub-frame was corroded. The vehicle was not repaired and remained at the dealer. The manufacturer was made aware of the failure. The failure mileage was approximately 125,000.
Tony Divino Toyota, a Toyota Motor Company dealership, sold me this vehicle sight unseen knowing I would immediately be towing a boat trailer 350 miles at highway speeds through construction zones on I-80 with children and our dog onboard. I was told it had passed a "160 point inspection" and was "in great condition". However, when delivered to me the dealership knew it was not road worthy and in fact illegal to drive on public roads due to missing a third brake light, bad rear brakes were bad, the transmission had failed, the battery had failed, the shocks/struts had failed, and a live shotgun shell was rolling around under the drivers seat. Both Toyota Motor Corporation and the dealership refused to address or correct these vehicle defects which could have resulted in a disastrous crash with injury/death to myself and children. This systemic Toyota disregard for used vehicle quality creates a national safety issue with all cars processed through the Toyota Motor Company network.
WHEN I'M SLOWING DOWN FOR A RED LIGHT, THEN THE LIGHT TURNS GREEN. AND I HIT THE ACCELERATION THE CAR WOULD JERK. AND SAME THING WHEN I MAKE A LEFT TURN. IT WOULD JERK AND FEELS LIKE I HAVE NO ACCELERATION.
I HAD MY BRAKES CHECKED OUT AT A SHOP IN MOUNTAIN HOME ARKANSAS, MOUNTAIN MOTORS HWY 5 N.. ASKING THAT THEY BLEED AND INSPECT AS NECESSARY ,AND CHECK TORQUES. AFTER AN HOUR AND TWENTY MINUTES I WAS TOLD THAT THE BLEEDER ON ONE CALIPER BROKE OFF! THEY DID NOT REPLACE THE BLEEDER, THEY SAID IT WOULD BE OK! THE BRAKES FAILED COMPLETELY LESS THAN 1000 LATER! WE WERE LUCKY, THE PEDAL WENT TO THE FLOOR IN A SMALL TOWN IN WISCONSIN. WE WERE MOVING SLOW AND I COASTED INTO A PARKING LOT! THE VEHICLE HAD TO BE TOWED AND $750.00 LATER WE CONTINUED OUR TRIP. THERE IS NO REGULATORY AGENCY IN ARKANSAS,AND THE REPAIR SHOP IS IGNORING ME! CAN YOU HELP? I HAVE RECIEPTS.
Showing 12 of 66 complaints.
NHTSA frontal crash test
Rated configuration: 2008 Toyota Sequoia 4-DR w/SAB